No.000110 Precision Visual Inspection Using Camera

Good IDEA!

2

Selection criteria

Stable linear motion is required often.

Back to page top.

Available sizes

■Miniature Linear Guides - Long Blocks

Material	Hardness
Stainless Steel (440C Stainless Steel)	56HRC-
Carbon steel (SCM, etc. alloy)	58HRC-

■Sizes and Dimensions.

Number of Blocks	Block Width	Block Length	Overall Height	Rail Length
1	12	21	6	40-100
	17	32	8	40-130
	20	40	10	65-275
	27	45.8	13	70-470
	32	58.3	16	110-670
	40	67.7	20	160-700
2	12	21×2pcs.	6	70-100
	17	32×2pcs.	8	85-130
	20	40×2pcs.	10	95-275
	27	45.8×2pcs.	13	120-470
	32	58.3×2pcs.	16	150-670
	40	67.7×2pcs.	20	220-700

* Please see the product pages for details of selectable sizes.

Back to page top.

Selection Steps

■Miniature linear guide selection steps.

Back to page top.

Accuracy Info

■Preload and Accuracy Standards (Long Blocks / Light Preload / High Grade).

Back to page top

Performance info.

Load Rating of Linear Guides (Standard block / Light Preload / High Grade).

Back to page top.

Technical Calculations

Operating Life Calculation for Linear Guides.

Operating Life.

When the linear guide is loaded in linear reciprocating motion, scaly damages called flaking appear due to material fatigue as the stress works on the rolling elements (steel balls) and the rolling contact surfaces (rails) constantly.Total travel distance until the first flaking occurs is called Life of Linear Guides.

Rated life.

Rated life is the total travel distance that 90% of linear guides of the same type can reach, under the same conditions, with no occurrence of flaking damage.Rated life can be calculated with the basic dynamic load rating and the actual load applied on the linear guides, as shown below.

Load must be calculated before actually using linear guides.To obtain loads during linear reciprocating motion, it is necessary to fully consider vibrations and impacts during motion as well as distribution condition of the load applied to linear guides. So, it is not easy to calculation the loads.In addition, the factors as operating temperature also significantly affect the life. Considering these conditions, the above-mentioned calculation formula will be as follows.

• L: Rated Life (Km).
• fH: Hardness Factor (See Fig.1).
• fT: Temperature Factor (See Fig.2).
• fC: Contact Factor (See Table-1).
• fW: Load Factor (See Table-2).
• C: Basic Dynamic Load Rating (N).
• P: Applied Load (N).

Hardness factor (fH).

For Linear Guide applications, sufficient hardness is required for ball contact shafts.Inappropriate hardness causes less allowable load, resulting in shorter life.
Please correct the rated life with the hardness factor.

Temperature factor (fT).

When the temperature of linear guides exceeds 100 C, the hardness of guides and shafts will be reduced, and the allowable loads will also be reduced compared to being used at room temperature, causing a reduction of life.Please correct the rated life according to the temperature factors.
* Please use Linear Guides at within the heat resistance temperature ranges shown on product pages.

Contact factor (fC).

Table-1. Contact factor.

Number of blocks per rail Contact factor fC.

1	1.00
2	0.81
3	0.72
4	0.66
5	0.61

For actual applications, more than 2 blocks are generally used per shaft.In this case, the load applied to each block varies depending on machining precision and is not uniformly distributed.As a result, per-block allowable load varies depending on the number of blocks per rail.Please compensate rated life with Contact Factors on Table - 1.

Load Factor (fW).

Table-2. Load factor.

Conditions of Use	fw
No shocks/vibrations, low speed: 15m/min. or less	1.0-1.5
No significant shocks/vibrations, medium speed: 60m/min. or less	1.5-20
With shocks/vibrations, high speed: 60m/min. or more	2.0-3.5

To calculate load applied to the Linear Guides, in addition to object weight, it requires inertia force attributed to motion velocity or moment loads.However, it is difficult to calculation the load accurately due to potential vibrations and shocks caused by other element than repeated start-stop motions during reciprocating motion.Thus, table-2 load factor helps simplify the life calculation.

Applied Load P Calculation Method.

When load is applied to the a block, convert moment load into applied load by the following formula.

• P: Applied Load (N).
• F: Downward load (N).
• C0: Static load rating (N).
• MA: Allowable static moment - Pitching direction (N・m).
• MC: Allowable static moment - Rolling direction (N・m).
• Lp: Load point distance (m) in pitching direction.
• Lr: Load point distance (m) in rolling direction.

Back to page top

Selection criteria

The slim body is suitable for the parts layout.

Back to page top.

Available sizes

■Locating Screw Stopper Blocks L-Shaped Bottom Mounting Type Fine Thread

Material	Surface Treatment	Adjusting Screw Type
		Coarse Thread	Fine Thread
1045 Carbon Steel	Black Oxide	○	○
	Electroless Nickel Plating	○	○
304 Stainless Steel	−	○	−

■Sizes and Dimensions.

Adjustment Screw				Overall Height	Overall Width	Overall Length	Plate Thickness	Mounting Screw
Diameter	Pitch		Center Height
	Coarse Thread	Fine Thread
M3	0.5	0.35	15・20	Center Height ＋4	9	25	6	M4
M4	0.7	0.5
M5	0.8	0.5	15	Center Height ＋6	12	32	8	M5
M6	1	0.75
M8	1.25	0.75	25・30・35	Center Height ＋10	22	44	10	M6
M10	1.5	1
M12	1.75	1
M16	2	1.5	35・40	Center Height ＋15	30	65	15	M8
M20	2.5	1.5

Back to page top.

Selection criteria

Standards to secure the required height accuracy.

Back to page top

Available sizes

■Support Pins- Flat, Round, Flat, Threaded

Material	Surface Treatment	Hardness
1045 Carbon Steel	Black Oxide	−
	Hard Chrome Plating	-
	Black Oxide	Treated Hardness 45 - 50 HRC
	Hard Chrome Plating	Heat treated hardness 45〜50HRC
304 Stainless Steel	-	-
440C Stainless Steel	−	Heat treated hardness 50〜55HRC

■Sizes and Dimensions.

Pin Dia.	Pin section length	Thread		Wrench flats
	0.01 mm Increments	DIA. (Coarse)	Length
φ6	10.00〜50.00	M3	4.5	5
φ8		M5	7.5	7
φ10	20.00〜80.00			8
φ12				10
φ15		M8	12	13
φ20				17

Back to page top

Accuracy Info

■Accuracy of Support Pins Flat Type.

Pin DIA. Tolerance:　±0.1.

Pin Section Length Tolerance:　+0.05/0.

Back to page top.