(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
Our Business Hours:
Mon. - Fri. 8 a.m. - 6 p.m.
Mon. - Fri. 8 a.m. - 6 p.m.
All Categories
Categories
- Automation Components
- Linear Motion
- Rotary Motion
- Connecting Parts
- Rotary Power Transmission
- Motors
- Conveyors & Material Handling
- Locating, Positioning, Jigs & Fixtures
- Inspection
- Sensors, Switches
- Pneumatics, Hydraulics
- Vacuum Components
- Hydraulic Equipment
- Spray Equipment And Accessories
- Pipe, Tubes, Hoses & Fittings
- Modules, Units
- Heaters, Temperature Control
- Aluminum Extrusions, Framing, Support & Posts
- Casters, Leveling Mounts, Posts
- Doors, Cabinet Hardware
- Springs, Shock Absorbers
- Adjustment/Fastening Components, Pins, Magnets
- Antivibration, Soundproofing Materials, Safety Products
- Fasteners
- Materials
- Wiring Components
- LAN Cables / Industrial Network Cables
- Equipment Specific Cables
- Cordsets
- Computer & AV Cables
- Wire/Cable
- Connector (General Purpose)
- Crimp Terminal Components
- Cable Organization
- Cable Gland Components
- Cable Bushing/Clip/Sticker
- Screw/Spacer
- Cable accessories
- Tube
- Electrical Conduits
- Duct/Wiring
- Electrical Wiring Tools
- Dedicated tools
- Soldering supplies
- Electrical & Controls
- Cutting Tools
- Carbide End Mill
- HSS End Mill
- Concrete Drill Bits
- Milling Cutter Insert / Holder
- Core Drill Bits
- Customized Straight Blade End Mill
- Dedicated Cutter
- Crinkey Cutters
- Turning Tool
- Drill
- Cutting Tool Accessories
- Screw Hole Related Tools
- Reamer
- Electric Drill Bits
- Chamfering, Centering Tool
- Hole Saws
- Magnetic Drill Press Cutters
- Step Drills
- Wood Drills & Cutters
- Processing Tools
- packing & logistics storage supplies
- Safety Products
- research and development & cleanroom supplies
- Press Die Components
- Plastic Mold Components
- Ejector Pins
- Sleeves, Center Pins
- Core Pins
- Sprue bushings, Gates, and other components
- Date Mark Inserts, Recycle Mark Inserts, Pins with Gas Vent
- Undercut, Plates
- Leader Components, Components for Ejector Space
- Mold Opening Controllers
- Cooling or Heating Components
- Accessories, Others
- Components of Large Mold, Die Casting
- Injection Molding Components
- Purging Agent
- Injection Molding Machine Products
- Accessories of Equipment
- Auxiliary Equipment
- Air Nippers
- Air Cylinders
- Air Chuck for Runner
- Chuck Board Components
- Frames
- Suction Components
- Parallel Air Chuck
- Special Air Chuck
- Mold Maintenance
- Heating Items
- Heat Insulation Sheets
- Couplers, Plugs, One-touch Joints
- Tubes, Hoses, Peripheral Components
Applications
Brands
- Webcode Seach | Series
-
#CODE
- Discontinued Products
Bolting Joints For Mold Cooling -For High Temperature (Heat-Resistant 120degree Series) / Straight Joints- (M-NSC10-03)
- Volume Discount
•Connecting Part: Hose
•Heat Proof: 120℃
•Includes Valve: No valve
•Shape: Straight
•Spanner Installation Section
Part Number
Configured Part Number is shown.
M-NSC10-03
Stainless steel SUS316(S31600)(1.4401)Brass C3604(C36000)(CU-ZN) Thread JIS B 0203 tapered thread for tubing R (PT)
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...
Loading...
Specifications
| Matching tubes | Tube inserting hole | *d | L | a | Cap nut | Metal body | Part Number | |||||
| Outer×Inner dia. | Hole dia. P | Depth C | F | B1(side to side) | ℓ1 | B2(side to side) | R(PT) | Type | No. | |||
| 6×4 | 6 | 6 | 3 | 25.5 | 21.5 | 11.5 | 12 | 8 | 12 | 1/8 | M-NSC (Stainless steel) | 6-01 |
| 28.5 | 22.5 | 11 | 14 | 1/4 | 6-02 | |||||||
| 29.5 | 23.2 | 12 | 17 | 3/8 | 6-03 | |||||||
| 8×6 | 8 | 7 | 5 | 27.5 | 23.5 | 13.5 | 14 | 8 | 14 | 1/8 | 8-01 | |
| 30.5 | 24.5 | 11 | 1/4 | 8-02 | ||||||||
| 31.5 | 25.2 | 12 | 17 | 3/8 | 8-03 | |||||||
| 10×7.5 | 10 | 9 | 6 | 33.5 | 27.5 | 16.5 | 17 | 11 | 17 | 1/4 | 10-02 | |
| 34.5 | 28.2 | 12 | 3/8 | 10-03 | ||||||||
| 37.5 | 29.3 | 15 | 21 | 1/2 | 10-04 | |||||||
| 12×9 | 12 | 9 | 7.5 | 33.5 | 27.5 | 16.5 | 19 | 11 | 19 | 1/4 | 12-02 | |
| 34.5 | 28.2 | 12 | 3/8 | 12-03 | ||||||||
| 37.5 | 29.3 | 15 | 21 | 1/2 | 12-04 | |||||||
| 6×4 | 6 | 6 | 3 | 22 | 18.0 | 11 | 10 | 8 | 10 | 1/8 | M-NKC (Brass) | 6-01 |
| 8×6 | 8 | 7 | 5 | 24 | 20.0 | 12 | 12 | 8 | 12 | 1/8 | 8-01 | |
| 27 | 21.0 | 11 | 14 | 1/4 | 8-02 | |||||||
| 10×7.5 | 10 | 9 | 6 | 29.8 | 23.8 | 14.8 | 16 | 11 | 16 | 1/4 | 10-02 | |
| 31.8 | 25.5 | 12 | 17 | 3/8 | 10-03 | |||||||
| 12×9 | 12 | 9 | 7.5 | 30.4 | 24.4 | 15.4 | 17 | 11 | 17 | 1/4 | 12-02 | |
| 32.4 | 26.1 | 12 | 3/8 | 12-03 | ||||||||
Use hot water tube (M-SFT 
Click here).More Information
■Bolting Joints High temperature type (Heat-resistant 120°C series)
Tube Installation/Removal
(1)Attaching tube
Check if the tube end is squarely cut (at a right angle), and it is not damaged or deformed.
Insert the tube fitted with a cap nut to the root of the tube insert.
Tighten the hexagonal part of the cap nut, to fit to the mold body with a spanner.
Lightly pull the tube to make sure that it will not come out.
When fitting the tube to bolting joints (M-NSC) again, fit it after cutting the part fitted before.
Usage without cutting could cause the tube to fall off unexpectedly or result in water leakage.
(2)Tightening the screw
Tighten the hexagonal part or body rectangular part with a spanner.
Since sealing materials are not put on the tapered thread for tubing, use sealing tapes or sealing materials if necessary.
(When using/applying sealing tapes or sealing materials, leave 1.5 to 2.0 thread from the end of the screw.)
(3)Detaching the tube
Detach the tube after holding the hexagonal part with a spanner and detaching the cap nut with another spanner.
Be sure to stop the fluid such as water and air before detaching the tube.
Notes
Before removing the joint, make sure to check that the pressure from inside the tube has come down to zero and the temperature of the fluid (water) to below 30°C for avoiding any accidents that may result from splashed hot fluid.
Keep the joint body free of load(such as tension, torsion or bending to protect it from damage)
Do not apply percussion flow (water hammer) to the joint.
Use hot water tube (M-SFT 
Click here).
Tube Installation/Removal
(1)Attaching tube
Check if the tube end is squarely cut (at a right angle), and it is not damaged or deformed.
Insert the tube fitted with a cap nut to the root of the tube insert.
Tighten the hexagonal part of the cap nut, to fit to the mold body with a spanner.
Lightly pull the tube to make sure that it will not come out.
When fitting the tube to bolting joints (M-NSC) again, fit it after cutting the part fitted before.
Usage without cutting could cause the tube to fall off unexpectedly or result in water leakage.
(2)Tightening the screw
Tighten the hexagonal part or body rectangular part with a spanner.
Since sealing materials are not put on the tapered thread for tubing, use sealing tapes or sealing materials if necessary.
(When using/applying sealing tapes or sealing materials, leave 1.5 to 2.0 thread from the end of the screw.)
(3)Detaching the tube
Detach the tube after holding the hexagonal part with a spanner and detaching the cap nut with another spanner.
Be sure to stop the fluid such as water and air before detaching the tube.
Notes
Before removing the joint, make sure to check that the pressure from inside the tube has come down to zero and the temperature of the fluid (water) to below 30°C for avoiding any accidents that may result from splashed hot fluid.
Keep the joint body free of load(such as tension, torsion or bending to protect it from damage)
Do not apply percussion flow (water hammer) to the joint.
Use hot water tube (M-SFT Click here).Basic Information
| Connecting parts | Hose | Heat proof | 120℃ | With/without valve | No valve |
|---|---|---|---|---|---|
| Shape | Straight | Spanner installation section | Yes |
Please check the type/dimensions/specifications of the part M-NSC10-03 in the Bolting Joints For Mold Cooling -For High Temperature (Heat-Resistant 120degree Series) / Straight Joints- series.
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Products like this...
| Part Number |
|---|
| M-NKC12-03 |
| M-NKC6-01 |
| M-NKC8-01 |
| M-NSC12-02 |
| M-NSC12-03 |
| M-NSC6-01 |
Additional Products in this Category
- Quick-Fitting Joints For Mold Cooling -Standard Type (Heat-Resistant 60degree Series) /Straight Joints /For Hexagonal Wrench Installation-
- Quick-Fitting Joints For Mold Cooling -Integrated Plugs・Sockets/(Heat-Resistant 99degree Series)/Straight Joints-
- Quick-Fitting Joints For Mold Cooling -Integrated Plugs・Sockets/(Heat-Resistant 120degree Series) /Straight Joints-
- Quick-Fitting Joints for Mold Cooling - Separate Plugs and Sockets, Heat-Resistant to 99 °C, O-Ring
- Quick-Fitting Joints For Mold Cooling -Separate Plugs・Sockets/Socket Screw-
- Quick-Fitting Joints For Mold Cooling -Separate Plugs・Sockets/(Heat-Resistant 120degree Series)/Sets-
- Bolting Joints For Mold Cooling -For High Temperature (Heat-Resistant 120degree Series)/L-Shaped Joints-
- Quick-Fitting Joints For Mold Cooling -Integrated Plugs・Sockets (Heat-Resistant 120degree Series) /L-Shaped Joints-
Complementary Products
-
Bolting Joints For Mold Cooling -For High Temperature (Heat-Resistant 120degree Series)/L-Shaped Joints-
MISUMI Days to Ship : 8 Days or more
-
Quick Fitting Joints for Mold Cooling - Straight Joint Plug- Spanner Type (Heat-Resistant 60 degree series) 【10-30 Pieces Per Package】
MISUMI Days to Ship : 10 Days or more
-
Bolting Joints for Mold Cooling - High Temperature type(Heat-Resistant 180degree series)/L-shapped Joint 【10 Pieces Per Package】
MISUMI Days to Ship : 10 Days or more
Tech Support
- Technical Support
- Tel：+52-442-672-7661 ext. 2 then wait and dial 4
E-mail: soportetecnico@misumimex.com - Mon. - Fri. 8 a.m. - 6 p.m.
- Technical Inquiry
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy